EdgeGrip Safety Glow Stair Nosings

These anti slip stair nosings use glow in the dark resins to help increase safety & visibility on your premises.

Stock Code: EG750GL

Why Choose EdgeGrip Safety Glow Anti Slip GRP Stair Nosings?

 

  • Glow in the dark technology - our Safety Glow Stair Nosings Glow in the Dark for between 3 - 4 hours.

  • Quick installation - drill down with mechanical fixings and you're good to go. Minimal downtime and can be walked on immediately.

  • The contrasted nosing also makes them Building Regulation and Disability Discrimination Act compliant.

  • Installs over virtually any substrate.

How to Install

 

Preparation

  • Ensure that the area is clean, dry and free from loose and friable material. Any “dished” or damaged surface areas should be patch repaired to provide a reasonably flat and consistent surface. You can patch repair concrete with our SlipGrip Step Edge Repair.

  • Dry fit stair nosings to ensure they fit freely and that they sit flat down on the surface. If required, SlipGrip can be trimmed on site to suit, ideally using a skill saw with a 4mm diamond blade or an angle grinder with a 1mm blade.

  • Please ensure that goggles and gloves are worn at all times when any form of cutting is involved.

 

Fixing Kit Application

  • Apply a 6mm bead (this may need to be increased dependant on the substrate conditions) of the high strength gap filling adhesive around the periphery of the underside of the stair nosings approx. 15mm in from the edges. If you are fixing your nosing to carpet or similar material - you can skip the adhesive section of the application. The adhesive is best applied using a skeleton gun.

  • Immediately press the panel firmly to the substrate to ensure adequate transfer of adhesive (depending on the size of the bead, this will elevate the sheet by approximately 1-1.5mm). A firm bond will be achieved in about one hour under normal circumstances and conditions.

  • Drill two holes on each side of the stair nosing, the first approximately 15mm in from each edge. For larger nosings, it may be necessary to have further fixing points in the centre of the tread. Pre-drilling the holes before drilling into the substrate is recommended.

Technical Data Sheet Download

Mechanical Data Sheet Download

Sizes

  • Lengths: 750mm, 1000mm, 1500mm, 2000mm or 3000mm

  • Profile: 70mm x 30mm

  • Thickness: 3mm with grit

 

FibreGrid offer a free cut-to-size service if the above sizes aren't suitable for you. Call 01440 712722 now to place your bespoke order.

All prices are for Next Day Delivery when ordered before 1pm. Prices shown are excluding VAT.

Order Value United Kingdom Mainland
£100 and under £8.95
£100.01 to £300 £16.00
£300.01 to £500 £25.00
£500.01 to £750 £29.50
£750.01 to £1000 £37.00
£1001.01 to £1500 £52.00
£1500.01 to £2000 £67.00
£2000.01 to £3000 £95.00
£3000.01 to £4000 £120.00
£4000.01 and over £300.00


Order Value Highlands and Islands*
£100 and under £20.00
£100.01 to £500 £100.00
£500.01 to £1000 £200.00
£1000.01 to £3000 £280.00
£3000.01 and over £300.00


Order Value Europe Zone 1 & Northern Ireland**
£100 and under £35.00
£100.01 to £3000 £150.00
£3000.01 to £6000 £250.00
£6000.01 and over Please call 01440 712722 for a bespoke quote.

 

* Highlands and Islands include - the Scottish Highlands and Islands, Isle of Wight, Isle of Man and the Channel Islands. ** Countries included in Europe Zone 1 - Southern Ireland, France, Germany, Luxembourg, Netherlands & Belgium. For all deliveries outside Europe Zone 1, please call 01440 712722 to place your order.

We have placed cookies on your device to help make this website better.